Dallas, Texas Laptop 13 Inch Lcd Replacement

 if you have a laptop and have a broken Screen, bleeding screen, or lines thru it, we can help.

A broken screen is one of the most frustrating things that can happen to a laptop owner. Not only is it unsightly, but it can also be expensive to fix. In some cases, the damage is so severe that the entire laptop needs to be replaced.

There are a few things that can cause a laptop screen to break. The most common is physical damage, such as dropping the laptop or bumping it into something. Other causes include defective hardware or a manufacturing defect.

There are a few ways to prevent a laptop screen from breaking. The most obvious is to be careful with it. Handle it gently and avoid dropping it or bumping it into things. If it is going to be stored in a backpack or case, make sure there is plenty of padding to protect it.

Another way to prevent screen damage is to use a screen protector. These are inexpensive and can be found at most office supplies or electronics stores. They are made of clear plastic and adhere to the screen. They will not completely prevent damage, but they will help to reduce it.

A step-by-step guide to changing the screen in a laptop

Before you replace the screen make sure to hook your laptop to the external display and make sure you need the new screen. it could be the graphics card sometimes. So make sure the screen is the one causing the issue. Make sure to disconnect the charger and battery and hold the power bottom for 30 seconds before getting started.

Finding the right model for the screen

Finding the right model LCD is important, just like the tire in the car. It comes in different variations. You can look for the model number in the back panel of your laptop and look for that model.


1. Pry the bezel off of the screen. A putty knife or a flathead screwdriver can do this.

Carefully pry the bezel off your Laptop. There might be some glue, so you can apply heat if necessary. Use the prying tool to slowly remove it.2.Remove the screws that hold the LCD to the metal bracket.

Using a Phillips screwdriver, remove the screws (usually four) that hold the LCD screen to the metal bracket. Keep them in a safe place as you'll need to reuse them later.

3. Disconnect the video cable from the LCD (typically a ribbon cable).

Gently pull the video cable out from the connector. You might need to use a flathead screwdriver to release the locking tabs on the connector.

4. Remove the LCD from the metal bracket.

Remove the LCD screen from the metal bracket.

5. Clean the LCD bracket.

Wipe down the bracket with a clean cloth to remove any dust or debris.

6. Install the new LCD into the bracket.

Line up the new LCD screen with the bracket and gently insert it. Make sure the video connector is properly seated in the connector.

7. Connect the video cable to the new LCD.

Gently insert the video cable into the connector on the new LCD. Make sure the locking tabs snap into place.

8. Screw the new LCD into the bracket.

Using the screws you removed earlier, screw the new LCD screen into the bracket.

9. Snap the bezel back into place.

Gently snap the bezel back into place around the new LCD screen.

You should now have a new, working LCD screen.

 

This guide should work for most models, but your model might be slightly different since there are multi-variation. You can follow the guide on the manufacturer’s website for more details.

Five Safety Measures while working with Laptop

Every computer technician should take a few safety measures while working with electronics. In this post, we'll discuss five of the most important ones.

1. Avoid Static Electricity

Avoiding static electricity is one of the most important safety measures while working with electronics. Static electricity can damage sensitive electronic components. To avoid static electricity, make sure you're grounded. You can wear a grounding strap or touch a metal ground surface before working with electronics.

2. Use Proper Ventilation

Working with electronics can produce harmful fumes. To avoid exposure to these fumes, make sure you work in a well-ventilated area. Open a window or use a fan to circulate the air if possible.

3. Use Insulated Tools

Another safety measure to take while working with electronics is to use insulated tools. This will protect you from shocks and help prevent damage to electronic components.

4. Be Careful with Water

Water and electronics don't mix. If you're working with electronic components, be careful not to spill any water on them. You could damage the components or cause an electrical shock if you do.

5. Disconnect Power Sources

Before working on any electronic equipment, ensure all power sources are disconnected. This includes unplugging the equipment from the wall and disconnecting any battery packs. Once you've followed these simple safety measures, you can help prevent damage to electronic components and avoid electrical shocks.



A broken screen is one of the most frustrating things that can happen to a laptop owner. Not only is it unsightly, but it can also be expensive to fix. In some cases, the damage is so severe that the entire laptop needs to be replaced.